The version numbers of the control boards will display and then all green console LED lights will turn on for 5 seconds. After you display all of the saved error codes, press the same selected key again to enter the diagnostic test cycle. The control will save and display up to 4 error codes. Press the same selected key to display and move past any other saved error codes.
WHIRLPOOL DUET STEAM CODE
After the 5th iteration, the control will display the last stored error code (F06). With the tub empty and the control off, select any one key except Stop/Cancel or Control Lock and press the key in this pattern: press and hold for 3 seconds, release, press and hold for 3 seconds, release, press and hold for 3 seconds, release, press and hold for 3 seconds, release, press and hold for 3 seconds. To enter the diagnostic test, plug in the washer and close the door. To clear the error code and reset the washer, run the diagnostic test. If the wire harness connections are okay, replace the steamer. Reconnect any loose wires or replace the wire harness if damaged. Leave your comment below.Unplug the washer and check the wire harness connections between the steamer and the steamer electronic control board. Aside from that, you don’t need tools to unlock your washer.ĭo you know friends who need some help with their locked washers? Please share this post with them! We also love to know what other problems you had with your washer and how you have solved them.
WHIRLPOOL DUET STEAM HOW TO
Conclusionĭid you learn much from our tutorial on how to unlock Whirlpool duet washer control lock? If your washer is not working, check if it is in the lock mode, then follow the instructions above. If there’s no problem with the washer mechanically, try changing the detergent you use. Also, don’t forget to set your washer in a Clean washer cycle. It will provide air circulation inside the washer to prevent mildew and molds. To ensure that your washer has been cleaned well, open your washer a little when not in use. But if it’s leaking only when running, take a look at the door boot, drain pump, and hose. If the washer is leaking even when turned off, check its valve or water supply. There are many reasons why your duet washer leaks. Press the Pause/Cancel button if you want to stop diagnosing the washer. Once done, run a duet washer quick diagnostic test. Reset the washer by unplugging it for 30 seconds to solve this problem. What will I do if my duet washer won’t lock? Press and hold this key for two to five seconds. After setting the washer, choose any key except “Power,” “Start,”and “Cancel”. Before starting the test, ensure that the washer is empty and on standby. If this method did not work, run the washer in the diagnostic mode. If you want to lock the washer again, you only need to press the unlocking button for about three seconds. If this doesn’t work, unplug the washer for five minutes and repeat this step. This means that you have successfully unlocked the washer. You will see a “Loc” icon disappear on the panel.
Once you have seen the unlocking button, press and hold it for about three seconds once you have seen it.
Step 2: Press the unlocking button for about three seconds Once you have found the panel, look for the unlocking button, then proceed to the next step. It is usually located on the panel at the top of the washer. After the washer has started, look for the button that indicates “Control Lock”. What to Do to Unlock Whirlpool Washer Control Lock Step 1: Look for the unlocking button of the washerīefore you can unlock your washer, you need to make sure it’s plugged in first. You may need an expert to fix your washer. If the tutorial doesn’t work after many tries, you should let a technician check your appliance. However, you can follow our technique with the Kenmore Elite Washer and Whirlpool Duet Dryer.Īs a piece of advice, make sure that your duet washer doesn’t have any problem with its wires. Check if your washer comes from the right brand since different washers have different steps for usage. If you don’t have any experience using mechanic gadgets, you can rest easy and follow the tutorial without using one.ĭuet washer: The only item that you need to prepare is your duet washer. To unlock control lock on whirlpool washer, you don’t need any power tools. Step 2: Press the unlocking button for about three seconds.Step 1: Look for the unlocking button of the washer.What to Do to Unlock Whirlpool Washer Control Lock.
0 kommentar(er)
